|
New Product: RFid Tag 13.56MHz
|
2013/07/10 |
|
RFid click Released
RFid click is an accessory board in mikroBUS form factor. It is a compact and easy solution for adding RFid to your design. It features a CR95HF 13.56 MHz contactless transceiver as well as a trace antenna. RFid click communicates with the target board microcontroller via mikroBUS UART (TX, RX), SPI (MISO, MOSI, SCK, CS) INT, RST, PWM and AN lines. The board is designed to use a 3.3V power supply only. An LED diode (GREEN) indicates the presence of power supply. CR95HF IC is a RFid module with an integrated transceiver for contactless applications. The board contains a dedicated internal frame controller and analog front end (AFE) for RF communications.
|
2013/07/10 |
|
New Product: Jacketed 1mm Fiber Optic Cable
|
2013/07/05 |
|
Fiber Opt click Released
Fiber Opt click is a compact and easy solution for adding fiber-optic communication to your design. It features IF-D91 fiber-optic photodiode, IF-E97 fiber-optic LED diode as well as two operational amplifiers. Provided plastic optic connectors feature an internal micro-lens and a precision-molded PBT housing to ensure efficient optical coupling with plastic fiber cable. Data rates of up to 512 Kbps can be achieved. The Fiber Opt Click communicates with the target MCU via UART interface or directly through the GPIO pins depending on the position of the J1 and J2 SMD jumpers. UART position is set by default.
|
2013/07/05 |
|
ccRF click Released
ccRF click is a low-power 2.4 GHz transceiver designed for the 2400- 2483.5 MHz ISM and SRD frequency bands. It features the CC2500 Low-Power 2.4 GHz RF transceiver as well as PCB trace antenna. The CC2500 is integrated with a highly configurable baseband modem that supports various modulation formats and has data rate up to 500 kBaud. Maximum device range is up to 20 meters in open space. ccRF click communicates with the target microcontroller via mikroBUS SPI, RST and PWM lines. The board is designed to use 3.3V power supply only. All these features make this board ideal for consumer electronics, wireless audio, wireless keyboard and mouse RF remote controls.
|
2013/07/05 |
|
New Product: miniUSB-B to USB-A Adapter
miniUSB-B Male to USB-A Female
|
2013/07/04 |
|
click USB adapter Released
The Click USB Adapter board provides the necessary interface for connecting Click add-on boards to your PC through a high speed USB connection, without the need for a microcontroller as a mediator. It features the FT2232H dual high speed USB to multipurpose IC, an Analog-to-Digital converter, EEPROM memory and a single mikroBUS host socket. The Click USB Adapter board can only be powered via USB cable. Two jumpers are provided on board; J1 jumper is used to select whether UART or I2C will be used, and J2 selects whether the AN pin in the mikroBUS socket will be a GPIO pin, or connected to the MCP3204 AD converter circuit.
|
2013/06/19 |
|
Adapter click Released
Adapter Click is a breakout board which simplifies the connection of add-on boards with mikroElektronika standard IDC10 headers to mikroBUS sockets. Connection can be made using either male or female IDC10 connectors. Both are provided with the package. You may solder a male IDC10 header on the top side of Adapter Click and connect the add-on board directly or via IDC10 flat cable. In some cases, a female header socket is a better choice. Solder it either on the top, or the bottom side, depending on which one is more convenient in the given circumstances. Each mikroBUS line is covered, except AN and RST. There are two jumpers for SPI/I2C selection and one for selection of power supply range.
|
2013/05/26 |
|
FM click Released
FM Click features the Si4703 IC, and is a complete FM radio tuner in the form of an add-on board. It supports worldwide FM band (76 - 108 MHz). The board contains two LM4864 audio amplifiers as well. The Si4703 has a nice set of features; such as automatic frequency and gain control, RDS/RBDS processor, seek tuning and volume control. FM antenna is provided through the earphones cable (recommended length between 1.1 and 1.45 m), which is plugged into on-board 3,5mm audio connector. FM Click has a simple I2C interface. All these features make this board ideal for MP3 players, portable radios, PDAs, notebook PCs, portable navigations and many more. The board is designed to use a 3.3V power supply only.
|
2013/05/23 |
|
Automatic DHL Shipping Cost Calculation
For international customers, we have now integrated automatic cost calculation for shipping via DHL Express into our online store. To try it out; please add a few items from the online store to your basket, and then begin the checkout process.
|
2013/05/20 |
|
GSM/GPRS AT Command Framework
Our SimPLC board is now on full release status. We have also put together a state-machine based framework for communicating with modules which have AT command interfaces, and this framework is included for free with any SimPLC purchase (alternatively also available for purchase separately). Although the framework is currently targeted at communicating with a GSM/GPRS module, it can also be adapted for other modules which communicate using AT commands.
The code currently includes facilities for sending and receiving SMSs, as well as detecting and reacting to missed calls.
For more information on the framework, please click here.
|
2013/05/16 |
|
EVE click (FT800) Released
EVE Click is a display controller board in mikroBUS form factor. It features the state-of-the-art FT800Q graphics controller which integrates display, audio and touch onto a low cost, easy-to-use, single-chip solution. With 12 embedded widgets, transparency and anti-aliasing support, PWM backlight dimming control and much more, the FT800Q brings fast and visually stunning graphics even to 8-bit MCUs with little Flash and RAM. It communicates with a microcontroller over SPI interface (up to 30 MHz). EVE click contains a flat cable connector, LM4864 audio amplifier, LED diode, and screw terminal audio connections. The board is designed to use a 3.3V power supply only.
|
2013/05/14 |
|
ConnectEVE (FT800) Released
ConnectEVE brings fast and visually stunning graphics to even low-cost 8-bit MCUs. It's state-of-the-art FT800 graphics controller integrates display, audio and touch onto a low cost, easy-to-use, single-chip solution. FT800 easily handles the 4.3" touch screen with 480x272px resolution. It has simple SPI interface with interrupt support and stereo audio output. Provided IDC10 and 1x10 headers are used to connect it to your development boards or existing final designs. mikroElektronika provide a free FT800 library for all of their mikroC, mikroBasic and mikroPascal compilers. Every feature of the controller is covered with a specialized function. Provided examples help you to get started quickly.
|
2013/05/14 |
|
GSM Booster (Telit GM862-QUAD Compatible) Released
GSM Booster is a pin-compatible replacement for the Telit GM862-QUAD module; retaining the same form factor as this popular, yet obsolete module. GSM Booster contains Telit's new GL865-QUAD GSM module, MMCX GSM antenna connector, SIM card holder and CSTP 50 pin vertical SMD molex connector (male) for further connection. It can be used on existing MikroElektronika development boards designed for the GM862. There are four zero-ohm SMD jumpers used to select whether Handsfree (HF) or Handset (MT) audio pins are used (soldered in the HF position by default).
|
2013/05/14 |
|
mikroMedia Plus for Stellaris Released
A large 4.3" TFT Touch Screen and over 20 on-board modules connected to a high-performance Stellaris ARM Cortex-M4 microcontroller with on-chip FPU and DSP.
|
2013/05/03 |
|
BarGraph click Released
BarGraph Click is a compact and easy solution for adding a ten-segment light bar display to your design. It features the JSB-R102510Z light bar display as well as two 74HC595 shift registers. The 74HC595 IC contains an 8-bit serial in, parallel/serial-out shift register as well as 8-bit storage register. BarGraph Click communicates with the target board microcontroller via mikroBUS SPI (MOSI, MISO, SCK, CS), RST and PWM lines. An SMD jumper is provided which allows the user to select whether the board will be powered with a 3.3V or 5V power supply.
|
2013/04/24 |
|
Light click Released
Light Click is the add-on board which features the PD15-22CTR8 PIN photodiode, providing an effective and easy way to measure ambient light intensity. It also features the MAX6106 voltage reference and MCP3201 ADC with SPI interface. Measured ambient light intensity is sent as an analog or digital signal to the main board microcontroller. Light Click communicates through mikroBUS SPI (MISO, SCK, CS) and AN lines. The PD15-22C-TR8 is a high photosensitive light sensor with fast response time. An SMD jumper allows the user to select whether the board will be powered with a 3.3V or 5V power supply.
|
2013/04/17 |
|
mikroMedia Plus for STM32F4 Released
mikroMedia Plus for STM32 is a compact, high-quality development board featuring the fast STM32F407ZGT6 MCU and 4.3" TFT touch-screen. It is also packed with a number of other features such as USB, microSD Card, accelerometer, audio codec, and more.
|
2013/04/12 |
|
FTDI click Released
FTDI Click features the FT2232H dual high speed USB 2.0 to UART/I2C/SPI serial interface converter. It includes a DA converter and EEPROM as well. The entire USB protocol is handled on the chip (FTDI USB drivers are required), making this board ideal for various USB applications. FTDI Click communicates with the target board via mikroBUS SPI (MOSI, MISO, SCK, CS), I2C (SDA, SCL), UART (Tx, Rx), RST, PWM, AN and INT lines. The board can be powered via USB or via mikroBUS socket. A green LED indicates the presence of power supply.
|
2013/04/12 |
|
