|
LED Ring click Released
LED Ring click is a mikroBUS add-on board with a ring of 32 red LEDs driven by four 8-bit 74HC595 serial-in, parallel-out shift registers. The ring is 25mm in diameter. The click communicates with the target MCU through the mikroBUS SPI interface, with RST, CS, SCK, MISO and MOSI pins marked MR#, LAT, CLK, DSOUT, DSIN, respectively. The board is designed to use either a 3.3V or 5V power supply only.
|
2016/07/12 |
|
FT230X Dongle Released
The FT230X Dongle is a breakout board for the FT230X USB to UART converter from FTDI Chip, but with a USB Type A Male connector instead of the usual Type B Female connectors found on most breakout boards of this type. This board has been designed for embedded applications (such as Raspberry Pi and BeagleBone Black) where more UARTS are required than what the embedded board is usually able to provide. The FT230X Dongle plugs straight into the USB port, eliminating the need for an extra USB cable. All relevant pins of the FT230X IC are exposed, and Power / Rx / Tx LEDs are also included on the board.
|
2016/06/26 |
|
Ribbon Cable 40-wire Released
20cm long, 40 wire.
Tip: Female to Female jumpers can be converted into either of the other two types, by simply inserting pins into their ends.
|
2016/06/08 |
|
Ribbon Cable 16-wire Released
20cm long, 16 wire.
Tip: Female to Female jumpers can be converted into either of the other two types, by simply inserting pins into their ends.
|
2016/06/08 |
|
Ribbon Cable 10-wire Released
20cm long, 10 wire.
Tip: Female to Female jumpers can be converted into either of the other two types, by simply inserting pins into their ends.
|
2016/06/08 |
|
DC Plug Extension Cable Released
Power Supply breakout / extension.
|
2016/06/08 |
|
Cap Extend click Released
Cap Extend click is a mikroBUS add-on board with a SEMTECH SX8633 low power, capacitive button touch controller. It has 12 pins for connecting capacitive inputs (either touch-buttons or proximity sensors). Any sort of conductive object can be used as an input. Additional 8 GPIO pins, available on the side-edges of the board, can be used as LED drivers. The SX8633 IC integrates a 10 bit ADC - a resolution high enough to support a wide variety of touch pad sizes and shapes to be used with the click. Cap Extend click communicates with the target MCU through the mikroBUS I2C interface, with additional functionality provided by RST and INT pins. Designed to use a 3.3V power supply only.
|
2016/06/08 |
|
3G click Released
3G-EA click is a versatile cellular network communication solution, featuring the compact 3G UMTS/HSPA Quectel UG95 module. This module features a full set of options for the cellular networking and communication, such as the network indication, embedded TCP/UDP stack, HTTP/HTTPS stack, full GSM/GPRS/EDGE implementation, UMTS/HSDPA/HSUPA protocol implementation and more. 3G-EA click features data-rates of 7.2 Mb/s (downlink) and 5.76 Mb/s (uplink) in HSPA mode. Onboard 16bit audio CODEC IC adds high-quality voice communication capability.
|
2016/06/08 |
|
Manometer click Released
Manometer click is an add-on board with a piezoresistive silicon pressure sensor. The onboard Honeywell HSCMAND060PA3A3 module has an industry-leading, extremely high accuracy of ±0.25%FSS BFSL. An absolute pressure range from 0 to 60 PSI makes it suitable for a variety applications. Beyond the measurement range, the sensor has a high burst pressure threshold, resulting in increased reliability. The barbed port accepts 4.93 mm (0.19") tubing. Manometer click communicates with the target board MCU through the mikroBUS I2C interface (SCL, SDA). Manometer click uses a 3.3V power supply.
|
2016/05/31 |
|
Accel 3 click (Accelerometer) Released
Accel 3 click is a mikroBUS add-on board with ST's H3LIS331DL low-power high-g 3-axis digital accelerometer. The IC has ±100g/±200g/±400g dynamically selectable full scales and outputs 16-bit data at rates from 0.5 Hz to 1 kHz. On the upper end, the chip can survive a 1000g high-shock. H3LIS331DL has extremely low power consumption (down to 1 micro amp in low-power mode). Advanced sleep-to-wakeup functions are also available. Accel 3 click can communicate with the target MCU either through the mikroBUS SPI or UART interface, with additional functionality provided by an interrupt pin (INT). The board is designed to use a 3.3 power supply only.
|
2016/05/31 |
|
WiFi5 click Released
WiFi 5 click is a mikroBUS add-on board with Gainspan's GS1500M ultra low-power Wi-Fi module with a PCB trace antenna (external IPX antenna connector also available). GS1500M supports Wi-Fi PHY speeds of up to 72.2mbps. The module is fully compliant with both IEEE 802.11b/g/n as well as with the requirements of the Wi-Fi alliance. Security features include support for WEP/WPA/WPA2, Adhoc and WPS (Wi-Fi protected setup). On the hardware side, the GS1500M module comprises two ARM7 44MHz chips (one for the radio, the other for applications), as well as on-chip Flash and SRAM. WiFi 5 click communicates with the target MCU through the mikroBUS UART interface (TX, RX), with additional functionality provided by RST and Prog pins (the latter in place of default mikroBUS AN pin).
|
2016/05/31 |
|
mikroMedia HMI 7.0" Released
A smart display solution, mikromedia HMI 7" has a high-brightness 800x480px color display on the front, and a powerful FT900Q 32-bit MCU with additional essential circuitry on the back - making it a standalone but cost-effective solution suitable for industrial applications.
|
2016/05/31 |
|
mikroMedia HMI 5.0" Released
A smart display solution, mikromedia HMI 5" has a high-brightness 800x480px color display on the front, and a powerful FT900Q 32-bit MCU with additional essential circuitry on the back - making it a standalone but cost-effective solution suitable for industrial applications. This model has the brightest display of all mikromedia HMI boards.
|
2016/05/31 |
|
mikroMedia HMI 4.3" Released
A smart display solution, mikromedia HMI 4.3" has a high-brightness 480x272px color display on the front, and a powerful FT900Q 32-bit MCU with additional essential circuitry on the back - making it a standalone but cost-effective solution suitable for industrial applications.
|
2016/05/31 |
|
