Our new website is in BETA! If you would like to take a look then please visit new.dizzy.co.za :-).

+27 (0)11 022 5323 +27 (0)64 681 8495
- -
VCP Monitor 2 Click (Go to Parent Category)

VCP Monitor 2 Click

VCP Monitor 2 Click is a three-channel, high-side current and bus voltage monitor with alert indication function ensuring the intended application works within desired operating conditions. Featured chip INA3221-Q1, by Texas Instruments, monitors both shunt voltage drops and bus supply voltages, in addition to having programmable conversion times and averaging modes for these signals. The INA3221-Q1 offers both critical and warning alerts to detect multiple programmable out-of-range conditions for each channel. The INA3221-Q1 senses current on buses that can vary from 0V to 26V. The device is powered from a single 2.7V to 5.5V supply, and draws 350 ??A (typical) of supply current. The I2C and SMBUS-compatible interface features four programmable addresses.

VCP Monitor 2 Click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

R295  Qty:
Price ex. VAT. Weight: 23g. Stock: Lead-time applicable [i]. mikroE Icon
  • Description

How does it work?

VCP Monitor 2 Click performs two measurements on up to three power supplies of interest (CH3 - CH1). The voltage developed from the load current passing through a shunt resistor creates a shunt voltage that is measured between the IN+ and IN- pins. The device also internally measures the power supply bus voltage at the IN- pin for each channel. The differential shunt voltage is measured with respect to the IN- pin, and the bus voltage is measured with respect to ground. The featured chip which is used for channel measurements, INA3221-Q1, is typically powered by a separate power supply that ranges from 2.7V to 5.5V. The monitored supply buses range from 0V to 26V.

Shop Click Boards Mixed Signal Measurements VCP monitor 2 Click

The INA3221-Q1 takes two measurements for each channel: one for shunt voltage and one for the bus voltage. Each measurement can be independently or sequentially measured, based on the Configuration mode settings. When the INA3221-Q1 is in the normal operating mode the device continuously converts a shunt-voltage reading followed by a bus-voltage reading. This procedure converts one channel, and then continues to the shunt voltage reading of the next enabled channel, followed by the bus-voltage reading for that channel, and so on, until all enabled channels have been measured. The programmed Configuration register mode setting applies to all channels. Any channels that are not enabled are bypassed in the measurement sequence, regardless of mode setting.

The INA3221-Q1 has two operating modes, continuous and single-shot, that determine the internal ADC operation after these conversions complete. When the INA3221-Q1 is set to continuous mode, the device continues to cycle through all enabled channels until a new configuration setting is programmed. The Configuration register MODE control bits also enable modes to be selected that convert only the shunt or bus voltage. This feature further allows the device to fit specific application requirements. In single-shot (triggered) mode, setting any single-shot convert mode to the Configuration register triggers a single-shot conversion. This action produces a single set of measurements for all enabled channels. To trigger another single-shot conversion, write to the Configuration register a second time, even if the mode does not change. When a single-shot conversion is initiated, all enabled channels are measured one time and then the device enters a power-down state. The INA3221-Q1 registers can be read at any time, even while in power-down. In addition to the two operating modes, the INA3221-Q1 also has a separate selectable power-down mode that reduces the quiescent current and turns off current into the INA3221-Q1 inputs. Power-down mode reduces the impact of the supply drain when the device is not used. Full recovery from power-down mode requires 40 µs. The INA3221-Q1 registers can be written to and read from while the device is in power-down mode. The device remains in power-down mode until one of the active MODE settings are written to the Configuration register.

VCP Monitor 2 Click also provides programmable thresholds that make sure the intended application operates within the desired operating conditions. Multiple monitoring functions are available using four alert pins: Critical, Warning, PV (power valid), and TC (timing control). The status of these alert pins are accessible over PCA9538A, a low-voltage 8-bit GPIO expander with interrupt and reset. The open-drain interrupt (INT) output is activated when any of the alert pins state has changed. This signal is used to inform the microcontroller that the bus voltage is not within the desired operating conditions. The PCA9538A uses the I2C communication protocol to read the current states of the alert monitoring pins with the changeable slave address to avoid bus conflict in advanced systems. For the visual representation of any deviation from programmed thresholds, alert monitoring pins are connected to 4 LEDs located on Click board™.

The VCP Monitor 2 Click supports the I2C communication protocol. Since there are two slave devices on the Click board™, the solderable SMD jumpers are conveniently placed for easy I2C slave address reconfiguration. The INA3221-Q1 has one cross-shaped jumper selection for one address pin with four possible addresses with connections to GND, VCC, SDA or SCL. The other one, PCA9538A, has two jumpers for address pins A1 and A0 with the possibility of four different slave addresses, making this Click board™ flexible for implementation in other systems with various peripherals sharing the same bus.

I2C Slave address selection

A1 A0 PCA9538A
GND GND 0x70
GND VCC 0x71
VCC GND 0x72
VCC VCC 0x73
A0 INA3221-Q1
GND 0x40
VCC 0x41
SDA 0x42
SCL 0x43

This Click board™ can be supplied and interfaced with both 3.3V and 5V without the need for any external components. The onboard SMD jumper labeled as VCC SEL allows voltage selection for interfacing with both 3.3V and 5V microcontrollers.


Type Measurements
Applications Electronic control units, digital clusters, rear-seat entertainment, infotainment, computers, power management, telecom equipment, battery chargers, power supplies, test equipment.
On-board modules VCP Monitor 2 Click uses the INA3221-Q1, a three-channel, high-side current and bus voltage monitor, from Texas Instruments and PCA9538A, an IO expander with interrupt and reset, from NXP Semiconductors.
Key Features Shunt voltage drops and bus supply voltages monitoring, programmable conversion times, critical and warning alerts, single power supply, 350 ??A of supply current
Interface I2C
Compatibility mikroBUS
Click board size L (57.15 x 25.4 mm)
Input Voltage 3.3V or 5V

Pinout diagram

This table shows how the pinout on VCP Monitor 2 Click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes Pin Mikrobus logo.png Pin Notes
NC 2 RST INT 15 INT Interrupt
Reset RST 3 CS RX 14 NC
NC 5 MISO SCL 12 SCL I2C Clock
Power Supply 3.3V 7 3.3V 5V 10 5V Power Supply
Ground GND 8 GND GND 9 GND Ground

Onboard settings and indicators

Label Name Default Description
LD1 PWR - Power LED Indicator
LD2 PV - Power Valid Alert LED Indicator
LD3 WRNG - Warning Alert LED Indicator
LD4 CRTCL - Critical Alert LED Indicator
LD5 TC - Timing-Control Alert LED Indicator
JP1 VCC SEL Left Power Supply Voltage Selection 3V3/5V, left position 3v3, right position 5v
JP2 VPU SEL Right INA3221-Q1 bias supply voltage for power valid output circuitry: left position - External supply, right position - On-board supply
JP3, JP5 ADDR SEL Left PCA9538A slave address selection: left position 0, right position 1
JP4,JP6 ADDR SEL Down INA3221-Q1 slave address 4-position selection: down - GND, up - VCC, left - SDA, right - SCL

VCP monitor 2 Click electrical specifications

Description Min Typ Max Unit
Supply Voltage (VCC) 0 3.3 6 V
Analog Inputs (IN+,IN-) -0.3 - 26 V
Bus Power Supply Rail (VPU) 0 - 26 V
Operating Temperature Range -40 - 125 °C

Software Support

We provide a library for the VCP Monitor 2 Click on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Library Description

The library contains basic communication with the module and allows the user to read and write data to the module. The user can read the current data of current, voltage and power measured by the sensor.

Key functions:

  • float vcpmonitor2_get_shunt_voltage ( uint8_t channel ) - Get Shunt voltage in mV
  • float vcpmonitor2_get_current ( uint8_t channel ) - Get Current data in mA
  • float vcpmonitor2_get_power ( uint8_t channel ) - Get Power in W

Examples description

The application is composed of three sections :

  • System Initialization - Initialization I2C module and RST pin on OUTPUT
  • Application Initialization - Initiaization driver init, device configuration for measurement, alert status reset and configuration
  • Application Task - Display Voltage on the BUS and Shunt, current and power data. Display Alert status informations.
void application_task ( )
    mikrobus_logWrite( ">> CHANNEL 1 <<", _LOG_LINE );
    display_channel_data( VCPMONITOR2_CHANNEL_1 );
    mikrobus_logWrite( ">> CHANNEL 2 <<", _LOG_LINE );
    display_channel_data( VCPMONITOR2_CHANNEL_2 );
    mikrobus_logWrite( ">> CHANNEL 3 <<", _LOG_LINE );
    display_channel_data( VCPMONITOR2_CHANNEL_3 );
    display_alert_status( );
    mikrobus_logWrite( "---------------------", _LOG_LINE );
    Delay_ms( 4000 );

Additional Functions :

  • display_alert_status() - Alert status
  • display_channel_data() - Channel data

The full application code, and ready to use projects can be found on our LibStock page.

Other mikroE Libraries used in the example:

  • I2C Library
  • UART Library

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.


This Click board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.

For more information about mikroSDK, visit the official page.