Our new website is available at new.dizzy.co.za :-).

X
+27 (0)11 022 5323 +27 (0)64 681 8495
Basket/Checkout
R
- -
Category: (Go to Store Home)
Folder Microcontroller Boards
Folder Accessory Boards
Folder Parts & Components
Folder Programmers
Folder Software
Folder Books
Folder Industrial Communication
Folder Production Equipment
Folder Miscellaneous
(i) Discounts
(i) Kits & Bundles
(*) On Special (96 items)
Catalogue Tool
Basket Basket: (Stock / Shipping Info)

Start adding items to your basket to see if any discount / free shipping is available for your order.
(Prices exclude VAT)
MagnifierSearch:
Step Up Click (Go to Parent Category)

Step Up Click

Step Up Click is a fixed frequency DC-DC step-up (boost) regulator, which can be obtained from any low voltage input - such as NiCd, NiMH or one cell Li-Po/Li-Ion batteries. This click features very high efficiency, low noise and anti-ringing voltage output and inrush current limiting with the internal soft-start, as well as true disconnect option for minimized power drain, when in shutdown mode. These features allow this device to be used as the power source for various battery-operated devices, such as microcontrollers, various portable embedded electronic devices, handheld instruments, GPS modules, or various battery-operated USB emergency backup chargers. Very good switching efficiency factor ensures prolonged battery life for any application this device is used in.

Step Up click board™ is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.
R470  Qty:
Price ex. VAT. Weight: 21g. Stock: Lead-time applicable [i]. mikroE Icon
3.3V Reg
3.3V Reg The 3.3V Reg Board features the MC33269DT-3.3 voltage regulator that consists of a 1.0V dropout composite PNP-NPN pass transistor, current limiting and thermal shutdown. This board offers embedded designers an economical solution for precision voltage regulation, while keeping the power losses to a minimum.
R200  Qty:
Price ex. VAT. Weight: 3g. Stock: Lead-time applicable [i]. mikroE Icon
5V / 3.3V Reg
5V / 3.3V Reg The 5V / 3.3VReg Board is an accessory board that includs both 5V and 3.3V on-board regulators. These regulators are used to reduce an input voltage from 8-16V AC/DC to 5V and 3.3V DC.
R290  Qty:
Price ex. VAT. Est. Weight: 10g. Stock: Lead-time applicable [i]. mikroE Icon
Uni-Reg
Uni-Reg The UNI-REG Board features a Step-Down Voltage Regulator LM2576 that enables voltage to change from 7-23V AC (or 9-32V DC) to 5V, 4V, 3.3V, 2.7V or 1.8V. The board components are clearly marked, which makes the connection easier.
R470  Qty:
Price ex. VAT. Weight: 30g. Stock: Lead-time applicable [i]. mikroE Icon
USB Reg
USB Reg USB REG Board is a simple and compact solution for powering your prototype device directly from USB. Board provides 5V directly from USB connector, but also features MC33269DT power regulator circut for creating 3.3V reference.
R145  Qty:
Price ex. VAT. Est. Weight: 5g. Stock: Lead-time applicable [i]. mikroE Icon
VREG click
VREG click VREG click is a digitally controlled DC Voltage regulator in mikroBUS™ form factor. The design is based on the well-known LM317 circuit, with the addition of a 12-bit DAC, 12-bit ADC, and an Operational Amplifier. Two pairs of screw terminals serve as inputs and outputs. The LM317 IC is a reliable regulator with typical line regulation of 0.01% and load regulation of 0.1%. It also has internal short-circuit current limiting and thermal overload protection. The circuit regulates voltage by turning all input/output difference into heat (effectively dissipating all the excess power). If it gets too hot it may damage the board or cause unexpected behaviour. Because of that, the board’s operating range is defined by two factors. 1) maximum input voltage and current (should not exceed 20V/1A); and 2) maximum wattage arising from current and I/O voltage difference (should not exceed 2W, measured as I x (Input V - Output V). The board also carries a MOSFET chip to toggle the output on and off. VREG click communicates with the target board MCU through the SPI interface (CS, SCK, MISO, MOSI). The board can use either a 3.3V or a 5V power supply. It is also possible to use the board’s power supply as the Input, by resoldering the onboard INPUT SEL jumper.
R575  Qty:
Price ex. VAT. Stock: Lead-time applicable [i]. mikroE Icon
VREG 2 click
VREG 2 click

VREG 2 click is a voltage regulator click, with outstanding performances. It has a steady output voltage with the ripple lower than 5mV, short circuit protection with the LED indicator, and high efficiency with minimal power dissipation. The main output regulation element is the LM317, a well-established adjustable voltage regulator, often used in various electrical designs, for its outstanding regulation characteristics. The supporting electronics allows for the reduced dissipation, voltage regulation and short-circuit indication. It consists of the LM358, a dual operational amplifier (op-amp) with high voltage gain, and the LM2596 buck converter. The VREG 2 click can be used with the input voltage in the range of 10V to 35V, and output voltage in the range of 2.5V to 15V, with current up to 600mA.
R495  Qty:
Price ex. VAT. Weight: 32g. Stock: Lead-time applicable [i]. mikroE Icon