DC connector
You can easily provide necessary power supply using this standard DC connector.
Accelerometer
On-board ADXL345 Digital Accelerometer allows you to measure acceleration.
Audio connector
Quadrupole audio connector enable you to connect headphones with microphone to the audio codec chip and use it in your applications.
Battery Charger circuit
TPS2041B Battery Charger circuit enables you to charge your Li-Polymer battery directly from USB port.
Battery connector
Li-Polymer battery connector allows you easier connection with your battery. Autonomous power supply will give your mikromedia the wings it deserves.
Battery Indicator LED
Whenever your board charges the battery, this LED will glow in red. When it’s fully charged it will change to green. Handy, isn’t it?
CC3000 WiFi Module
This popular wireless network processor supports had the best-in-class performance. It implements 802.11 b/g standards, and features embedded IPv4 TCP/IP stack, thus taking the load off the MCU.
Connection pads
Every unsused microcontroller pin is available through connection pads. They can be used to connect your mikromedia board with additional shields or accessory boards.
In-Circuit Debug Interface
Integrated In-Circuit Debug Interface (ICDI) enables programming and debugging right here on board. No additional hardware required.
LAN Filter
10/100/1000M LAN pulse transformer and filter.
RJ-45 Ethernet connector
High quality female socket for standard Ethernet cables with RJ-45 connector.
Ethernet Indicator LEDs
Two LEDs (Link and Ackowledge) are provided for monitoring ethernet communication.
Cortex Debug Connector
The Cortex Debug Connector supports JTAG debug, Serial Wire debug and Serial Wire Viewer operations (via SWO connection when Serial Wire debug mode is used).
Infrared Receiver
IR receiver diode enables you to remotely control your device.
TM4C129xNCZAD
High-performance Tiva™ C Series ARM® Cortex™-M4F microcontoller with on-chip FPU and DSP easily handles demanding applications.
Crystal Oscillator
25MHz crystal oscillator circuit that provides external clock is connected to microcontroller osc pins.
microSD card slot
microSD Card slot allows you to store large ammounts of data externally on microSD card using fast SPI communication.
Stereo Audio codec
VS1053 MPEG audio decoder with SPI interface for fast reproduction of Ogg Vorbis / MP3 / AAC / WMA / FLAC / MIDI audio files.
RF Transceiver
Nordic nRF24L01+ is a wireless ultra low power 2.4 GHz RF transceiver. It has a simple SPI interface.
ON/OFF Switch
Two position ON/OFF switch is a handy feature. It’s conveniently located right on the edge of the board.
Piezo Buzzer
With piezo buzzer you can debug your applications, or have audio signalization feature. It can be connected to two digital output pins, one of which is the output of PWM module.
Photosensor
PIN photosensor enables you to measure ambient light and respond by dimming or brightening up the screen backlight.
Power LED
We have added power indicator LED, so you can be sure whether your board has stable power supply.
Reset Button
High quality reset button with surrounding reset circuitry ensures stable reset operation.
Active RF chip antenna
Active RF chip antenna for 2.4 GHz RF transceiver.
RGB LED
Front side features RGB LED which is useful for simple visual signalization.
RTC battery
Lithium polymer battery is providided for retaining data and powering internal Real-Time Clock module of the microcontroller.
RTCC Crystal Oscillator
Board contains 32.768kHz Crystal oscillator (X1) which provides external clock for internal RTCC module.
Mounting Holes
Four mounting holes, one in each corner of the board, facilitate board integration.
SDRAM MT48LC4M16A2
MT48LC4M16A2 - 8MB SDRAM is not just a convenience, it’s a necessity. Use it to store images and resources for the large TFT touchscreen, and you’ll experience five times performance boost.
Temperature Sensor
Analog Temp. Sensor MCP9700A is used to measure temperature from -40ºC to 125ºC.
5” Touch Screen
800x480px Color TFT Display with Touch Panel can display vivid and clear color images or advanced graphic content.
Touch Screen Connector
Connector for the Touchscreen flat cable is located at the back of the board.
Debugging LEDs
Two LEDs are provided to indicate debugging/programming activities.
miniUSB connector
Microcontroler supports Full Speed and USB 2.0 OTG, so this connector allows you to communicate with a PC or other USB devices using USB connection.
Active WiFi Chip Antenna
Active 2.4GHz Chip antenna is specially tuned for CC3000 WiFi module. It ensures that you have the best wireless coverage.
JTAG emulator
On-board FT2232D chip provides debugging interface, serving as a JTAG emulator.
Up-Close
Hover your mouse over different parts of the board in order to view the details up-close.
