Our new website is available at new.dizzy.co.za :-).

X
+27 (0)11 022 5323 +27 (0)64 681 8495
Basket/Checkout
R
- -
Category: (Go to Store Home)
Folder Microcontroller Boards
Folder Accessory Boards
Folder Parts & Components
Folder Programmers
Folder Software
Folder Books
Folder Industrial Communication
Folder Production Equipment
Folder Miscellaneous
(i) Discounts
(i) Kits & Bundles
(*) On Special (96 items)
Catalogue Tool
Basket Basket: (Stock / Shipping Info)

Start adding items to your basket to see if any discount / free shipping is available for your order.
(Prices exclude VAT)
MagnifierSearch:
DC MOTOR 7 Click (Go to Parent Category)

DC MOTOR 7 Click

DC MOTOR 7 click is a dual brushed DC motor driving Click board™, featuring the advanced PWM chopper-type integrated DC motor driver, labeled as TB67H400AFTG. This IC can drive two brushed DC motors independently, using a wide range of supply voltages, while delivering reasonably high current to the connected DC motors. This is possible due to the low resistance of the integrated H-Bridges. In addition to being able to drive two independent DC motors, it can be used in a so-called large mode to drive a single motor, utilizing both bridges in parallel. This effectively doubles the amount of current it can deliver to the DC motor.

The Click board™ is supported by the mikroSDK compliant library, which includes functions that simplify software development. The Click board™ comes as a fully tested product, ready to be used on a system equipped with mikroBUS™.
R470  Qty:
Price ex. VAT. Weight: 38g. Stock: Lead-time applicable [i]. mikroE Icon
DC Motor click
DC Motor click DC MOTOR click is a DC motor driver board in the mikroBUS form factor. It features the DRV8833RTY H-Bridge motor driver, 74HC4053 multiplexer and two screw terminals. The 74HC4053 IC is incorporated into the design so that the motor can be run using only the one PWM line available on the mikroBUS socket. DC MOTOR click communicates with the target board via SELECT1, SELECT2 and nSLEEP control lines; PWM input line and nFAULT feedback line. The board is designed to use either a 3.3V or 5V power supply. It can be powered from the mikroBUS socket, or externally through the CN2 screw terminals (3-10V). It is limited to a 0.9A driving current and has a 0.22R current sense resistor. The motor is connected to the CN1 screw terminal.
R450  Qty:
Price ex. VAT. Est. Weight: 25g. Stock: Lead-time applicable [i]. mikroE Icon
DC Motor 2 click
DC Motor 2 click DC MOTOR 2 click carries the TB6593FNG driver IC for direct current motors. With two pairs of screw terminals (power supply and outputs), the click board can drive motors with voltages from 2.5 to 13V (output current of up to 1.2 amps with peaks up to 3.2 amps). The PWM signal drives the motor while the IN1 and IN2 pins provide binary direction signals that set the direction of the motor (clockwise or counter clockwise), or apply stop or short brake functions. Stop mode cuts off the power supply so the motor continues spinning until it runs out of momentum. Short break brings it to an abrupt stop.
On SpecialOn SpecialOn Special R200  R345  Qty:
Price ex. VAT. Est. Weight: 25g. Stock: 1 available immediately [i]. mikroE Icon
DC Motor 3 click
DC Motor 3 click DC MOTOR 3 click is a mikroBUS™ add-on board with a Toshiba TB6549FG full-bridge driver for direct current motors. The IC is capable of outputting currents of up to 3.5 A with 30V, making it suitable for high-power motors. Two pairs of screw terminals are positioned on the top of the board. One is for bringing an external power supply; the other is for connecting a motor. TB6549FG has four operating modes: clockwise, counter-clockwise, short brake and stop. The operating mode is configured through IN1 and IN2 pins. A separately controlled standby mode is also available. For safety, the TB6549FG IC incorporates overcurrent protetciont and a thermal shutdown circuit. The click communicates with the target MCU through the mikroBUS™ PWM pin, with additional functionality provided by IN1, IN2 and SLP pins (in place of default mikroBUS™ AN, RST and CS pins). Designed to use a 3.3 power supply only.
R470  Qty:
Price ex. VAT. Est. Weight: 20g. Stock: Lead-time applicable [i]. mikroE Icon
DC MOTOR 4 click
DC MOTOR 4 click DC MOTOR 4 click is capable of driving motors with a supply voltage from 4.5V to 36V. It carries the MAX14870 motor driver from Maxim Integrated. The click is designed to run on either 3.3V or 5V power supply. DC MOTOR 4 click communicates with the target MCU over the following pins on the mikroBUS™ line: PWM, AN, CS, and INT.
R365  Qty:
Price ex. VAT. Stock: Lead-time applicable [i]. mikroE Icon
DC MOTOR 5 click
DC MOTOR 5 click DC MOTOR 5 click carries the DRV8701 brushed DC motor gate driver from Texas Instruments. The click is designed to run on an external power supply. It communicates with the target MCU over the following pins on the mikroBUS™ line: AN, RST, CS, PWM, and INT.
R405  Qty:
Price ex. VAT. Stock: Lead-time applicable [i]. mikroE Icon
DC Motor 8 click
DC Motor 8 click

DC Motor 8 click is a DC motor driver. It can drive simple DC motors with brushes, providing them with a significant amount of current and voltage up to 40V. The click has one control input, that uses the PWM signal from the host MCU. It uses the half-bridge topology to regulate the speed of the motor rotation, employs advanced dead-time circuitry that monitors the output stage, providing maximum switching efficiency and features an advanced technique to avoid shoot-through currents.

Features, such as high-efficiency factor, low overall power consumptions and complete isolation of the output stage, enable this device to be used in various battery operated handheld tools, fans and in general - whenever a powerful and reliable DC motor driver is required.
R450  Qty:
Price ex. VAT. Weight: 25g. Stock: Lead-time applicable [i]. mikroE Icon