Tilt click Tilt click carries a RPI-1035, 4-directional optical tilt sensor. This type of sensor provides positional feedback for left, right, backward or forward movement (tilt). Compared to mechanical solutions, optical direction detectors are less prone to noise caused by vibrations. Compared to magnetic-based direction detectors, they are not influenced by magnetic disturbances. Tilt click communicates with the target board microcontroller through mikroBUS PWM and INT lines, used here for vout1 and vout2 outputs from the sensor. In addition, two onboard LEDs provide visual feedback from the sensor. The board is designed to use either a 3.3V or 5V power supply. R305  Qty: Add to Basket Price ex. VAT. Est. Weight: 20g. Stock: Lead-time applicable [i].

Accel click (Accelerometer) Accel Click is an accessory board in the mikroBUS form factor. It features the ADXL345 3-axis accelerometer module with ultra-low power and high resolution (13-bit) measurement. Module supports several sensing functions such as single/double tap detection, activity/inactivity monitoring, free-fall detection etc. It has a memory management system with a 32-level FIFO buffer to store data with minimized host processor activity. The board is designed to use 3.3V power supply only. R285  Qty: Add to Basket Price ex. VAT. Weight: 20g. Stock: Lead-time applicable [i].

Accel 2 click (Accelerometer) Accel 2 click carries ST's LIS3DSH IC, a low-power factory-calibrated three-axis accelerometer which embeds a FIFO buffer and two programmable state machines. It allows you to implement gesture recognition. User-defined programs can distinguish movement patterns like shake and double shake, face up and face down, turn and double turn, and activate an interrupt upon their execution. You can also switch between I2C and SPI interfaces for communicating with the target board MCU (by soldering the onboard jumpers in the appropriate positions). Accel 2 click is designed to use a 3.3V power supply only. On Special R270  R470  Qty: Add to Basket Price ex. VAT. Est. Weight: 20g. Stock: 1 available immediately [i].

Three-Axis Accelerometer The Three-Axis Accelerometer Board includes a small, thin, low-power, 3-axis accelerometer ADXL330 with signal conditioned voltage outputs. It measures acceleration with a minimum full-scale range of ±3 g. It comes with many ready-to-use examples. R635  Qty: Add to Basket Price ex. VAT. Weight: 5g. Stock: Lead-time applicable [i].

Shake2Wake click Shake2Wake click carries an ADXL362 ultralow power, 3-axis MEMS accelerometer from Analog Devices. The distinguishing feature of this IC is that it incorporates several activity detection modes. The interrupt pins from the chip are connected to an onboard ADP195 power switch IC that in turn controls an external device connected through a screw terminal. The detection threshold is configurable (both intensity and duration). The duration of inactivity that leads to switching off is also programmable. Shake2Wake click can also be used as a regular accelerometer, for continuous sensing, in which case it communicates with the target MCU through mikroBUS SPI interface. Uses 3.3V power supply only. R1,050  Qty: Add to Basket Price ex. VAT. Est. Weight: 20g. Stock: Lead-time applicable [i].

Accel 3 click (Accelerometer) Accel 3 click is a mikroBUS add-on board with ST's H3LIS331DL low-power high-g 3-axis digital accelerometer. The IC has ±100g/±200g/±400g dynamically selectable full scales and outputs 16-bit data at rates from 0.5 Hz to 1 kHz. On the upper end, the chip can survive a 1000g high-shock. H3LIS331DL has extremely low power consumption (down to 1 micro amp in low-power mode). Advanced sleep-to-wakeup functions are also available. Accel 3 click can communicate with the target MCU either through the mikroBUS SPI or UART interface, with additional functionality provided by an interrupt pin (INT). The board is designed to use a 3.3 power supply only. R495  Qty: Add to Basket Price ex. VAT. Est. Weight: 15g. Stock: Lead-time applicable [i].